sony CDP-608ESD - Compact Disc Player manual

The Sony CDP-608ESD is a high-fidelity compact disc player featuring advanced digital-to-analog conversion, dual D/A converters, optical digital output, remote control operation, programmable playback, and high-quality audio components for superior sound reproduction. Below are key sections covering features, installation, operation, specifications, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Audio Systems 7. Playing CDs 8. Advanced Functions 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-precision disc transport mechanism, Dual 16-bit D/A converters, Optical digital output, Remote control, Programmable memory, Direct track access.

Feature	Description
Dual D/A Converters	Separate converters for left and right channels for improved stereo separation
Optical Digital Output	For connection to external digital processors or recorders
Programmable Playback	Memory for up to 20 tracks in any desired sequence
Direct Track Access	Quick selection of tracks using numeric keypad
Repeat Functions	Repeat track, repeat all, or repeat programmed sequence
Remote Control	Full-function infrared remote for all operations
Headphone Output	Front panel jack with adjustable volume control
Display	Fluorescent display showing track, time, and status information
Audio Outputs	Fixed and variable line outputs
Power Supply	Stabilized power supply for consistent performance

Installation

Unpack and inspect contents. Place on stable, level surface away from heat sources and vibration.

Connect audio outputs: Use RCA cables to connect LINE OUT to amplifier or receiver.
Connect optical output: Use Toslink cable to digital input of compatible device.
Connect headphones: Plug into front panel headphone jack for private listening.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct voltage (check rating label).

First-Time Setup

Power on player; initialize system.

Load disc: Press OPEN/CLOSE, place CD label side up in tray, close tray.
Basic playback: Press PLAY to begin playback from first track.
Adjust output level: Use variable output control if connected to power amplifier directly.
Remote setup: Install batteries in remote control (typically two AA batteries).

CAUTION! Handle discs by edges only. Keep discs clean and free from scratches.

Specifications

Type: Compact Disc Player
Frequency Response: 2Hz-20kHz (±0.5dB)
Signal-to-Noise Ratio: >100dB
Dynamic Range: >96dB
Total Harmonic Distortion: <0.003%
Channel Separation: >95dB (1kHz)
Output Voltage: 2.0V RMS (fixed output)
Digital Output: Optical, 44.1kHz sampling
Power Requirements: 120V AC, 60Hz (or as per region)
Power Consumption: 18W
Dimensions: 430mm (W) × 110mm (H) × 320mm (D)
Weight: 7.5kg

Controls and Settings

Front Panel: POWER, OPEN/CLOSE, PLAY, STOP, PAUSE, SKIP/SEARCH buttons, DISPLAY, HEADPHONE jack with volume.

Remote: POWER, Numeric buttons (0-9), OPEN/CLOSE, PLAY, STOP, PAUSE, SKIP, SEARCH, PROGRAM, REPEAT, DISPLAY.

Basic Functions: Play, pause, stop, track skip (forward/backward). Search: Hold SKIP buttons for fast forward/reverse. Program: Press PROGRAM to enter programming mode, select tracks with numeric buttons. Repeat: REPEAT for track/all/program. Display: Shows track number, elapsed/remaining time, total tracks, programming information.

Connecting to Audio Systems

Audio Outputs: Fixed LINE OUT (for receivers with volume control), Variable LINE OUT (for direct amp connection). Digital Output: Optical for digital recording or processing.

Turn off all components before making connections.
Use high-quality RCA cables for audio connections.
For optical connection, remove protective caps and insert cable firmly until click.
Set amplifier to correct input source (CD, AUX, etc.).

Tip: Keep audio cables away from power cords to minimize interference.

Playing CDs

Supports standard audio CDs (CD-DA).

Insert disc: Press OPEN/CLOSE, place CD properly, press OPEN/CLOSE again to close.
Play: Press PLAY; player reads TOC then starts playback.
Stop: Press STOP; display shows total tracks and time.
Pause: Press PAUSE during playback; press again to resume.
Skip tracks: Press NEXT or PREV to skip forward or backward.
Search: Hold NEXT or PREV to fast forward or reverse through track.
Direct access: Enter track number using numeric buttons on remote.

WARNING! Do not move player during disc playback. Do not expose discs to direct sunlight or high temperatures.

Advanced Functions

Programming: Press PROGRAM, then enter track numbers in desired sequence (up to 20 tracks). Press PLAY to start programmed playback. Repeat: Press REPEAT repeatedly to cycle through repeat modes (track/all/program). Memory Check: During programming, press CHECK to review programmed sequence. Intro Scan: Press and hold PROGRAM then press PLAY to play first 10 seconds of each track.

Care & Maintenance

Unplug from power before cleaning. Use soft, dry cloth for exterior. For lens cleaning, use approved CD lens cleaner only.

CAUTION! Never use solvents or abrasive cleaners. Do not open chassis; no user-serviceable parts inside.

Regulatory Information

Complies with FCC rules Part 15 for Class B digital devices. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Sony is a registered trademark of Sony Corporation. For support, consult your authorized Sony dealer or visit Sony's support website.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord not connected	Check power cord connection; ensure outlet is working.
Disc does not play	Disc inserted upside down	Eject disc, insert with label side up.
Skip or mistracking	Disc dirty or scratched	Clean disc with soft cloth from center outward.
Remote not working	Batteries depleted or obstacles	Replace batteries; ensure clear path to sensor.
No sound from headphones	Volume control too low	Adjust headphone volume knob on front panel.
Display shows "NO DISC"	No disc or incompatible disc	Insert proper audio CD; ensure disc is not damaged.
Digital output not working	Cable not connected properly	Check optical cable connection at both ends.

Reset: Unplug power cord for 30 seconds, then reconnect.

Service: Contact authorized Sony service center for repairs.