Sony RMT-B119C Manual

The Sony RMT-B119C is a universal remote control designed for use with various Sony audio/video equipment, including TVs, DVD/Blu-ray players, sound systems, and set-top boxes. It features a user-friendly layout with dedicated function keys, learning capabilities for custom programming, and compatibility with multiple device codes. Below are key sections for overview, features, setup, programming, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Ergonomic design, LCD display (on select models), dedicated device keys (TV, DVD, AUDIO, etc.), numeric keypad, navigation pad, volume/channel controls, and special function buttons.

Feature	Description
Universal Compatibility	Controls up to 4 devices (TV, DVD/Blu-ray, Audio, Cable/Satellite)
Learning Function	Can learn commands from original remotes for custom keys
Direct Code Entry	Quick setup using 3-digit manufacturer codes
Macro Function	Program sequence of commands to a single button (if supported)
Backlit Keys	Illuminated buttons for low-light conditions (on select models)
Ergonomic Design	Fits comfortably in hand with intuitive button layout
Device Selector	Dedicated buttons (TV, DVD, AUDIO, CABLE) to switch control modes
Numeric Keypad	For direct channel/input selection
Navigation Pad	Directional arrows and OK/Enter for menu navigation
Special Functions	Menu, Guide, Info, Exit, Subtitle, Audio, etc.

Package Contents

Unpack and verify all items are present.

1. Sony RMT-B119C Remote Control (1 unit)
2. User Manual (this document)
3. Two AAA batteries (may vary by region)
4. Warranty information card (optional)

NOTE: If any item is missing or damaged, contact your retailer or Sony support.

Initial Setup & Battery Installation

Power on the remote by installing batteries.

1. Open battery compartment: Slide cover on back of remote.
2. Insert batteries: Place two AAA batteries, observing correct polarity (+/-).
3. Close compartment: Secure cover until it clicks.
4. Test remote: Point at device and press any button; LED should flash.
5. Program remote: Use auto-search or direct code entry for your device (see Section 6).

CAUTION! Use only AAA batteries. Do not mix old and new or different types. Remove batteries if not used for extended periods.

Specifications

• Model: RMT-B119C
• Power Source: 2 x AAA batteries (DC 3V)
• Battery Life: Approximately 12 months (typical use)
• Operating Range: Up to 7 meters (23 feet), within 30-degree angle
• Infrared Frequency: 38 kHz (standard)
• Compatible Devices: TVs, DVD/Blu-ray players, audio systems, cable/satellite boxes, streaming devices
• Learning Capacity: Up to 10 commands (if learning function supported)
• Dimensions: Approx. 150 mm x 50 mm x 20 mm (L x W x H)
• Weight: Approx. 100 g (including batteries)
• Operating Temperature: 0°C to 40°C (32°F to 104°F)

Controls and Layout

Top section: Device selector buttons (TV, DVD, AUDIO, CABLE). Center: Navigation pad, OK, Menu, Back. Lower: Numeric keypad, Volume/Channel, Mute, Power.

Key Functions: POWER (turns device on/off), MUTE (silences audio), VOL +/- (adjusts volume), CH +/- (changes channels), INPUT (cycles video sources), GUIDE (accesses program guide), INFO (displays program information), EXIT (closes menus), SUBTITLE (toggles subtitles), AUDIO (cycles audio tracks).

LED Indicator: Flashes red when button is pressed or during programming.

Programming the Remote

Two methods: Auto-search (recommended) or Direct Code Entry.

1. Auto-search (for TV):
   • Turn on TV manually.
   • Press and hold TV button until LED stays on.
   • Press POWER repeatedly until TV turns off.
   • Press OK to save code.
2. Direct Code Entry:
   • Find 3-digit code for your device in code list (see manual appendix).
   • Press and hold device button (e.g., DVD) until LED stays on.
   • Enter 3-digit code using numeric keypad.
   • LED blinks twice to confirm.
3. Test remote: Press POWER and other buttons to verify control.

Tip: If code doesn’t work, try auto-search or next code from list for same brand.

Operating Your Devices

Switch control between devices by pressing corresponding device button (TV, DVD, etc.).

1. Control TV: Press TV button, then use navigation, volume, channel keys.
2. Control DVD/Blu-ray: Press DVD button, then use Play, Stop, Pause, Menu.
3. Control Audio System: Press AUDIO button, then use Volume, Mute, Source.
4. Control Cable/Satellite: Press CABLE button, then use Guide, numeric keys.
5. Macro (if supported): Program sequence (e.g., "Watch DVD") to one button.

NOTE: Some functions may not be available for all devices; refer to device manual.

Learning Function (Custom Keys)

Allows remote to learn commands from original remote (if supported).

1. Place remotes head-to-head, 2-3 cm apart.
2. Press and hold LEARN button (if present) until LED lights.
3. On RMT-B119C, press key you want to program (e.g., a unused button).
4. On original remote, press key with command to learn (point at RMT-B119C).
5. LED blinks, then stays on if successful.
6. Repeat for other keys; press LEARN again to exit.

Limitations: Cannot learn all commands (e.g., power on/off may not be learnable). Maximum 10 learned commands.

Care & Maintenance

Remove batteries before cleaning. Wipe with dry, soft cloth; avoid liquids.

DO: Store in cool, dry place. Replace batteries when weak.

DON'T: Expose to extreme heat, moisture, or direct sunlight. Do not disassemble.

Regulatory Information

FCC Part 15: Class B digital device; complies with limits for residential use. ICES-003: Complies with Canadian EMI regulations. Sony and RMT-B119C are trademarks of Sony Corporation. For support, visit www.sony.com/support or contact Sony Customer Service at 1-800-222-7669 (US).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote doesn't work	Dead batteries, obstruction, wrong mode	Replace batteries; point directly at device sensor; press correct device button (TV/DVD).
Some buttons not working	Incorrect code, device limitation	Reprogram with correct code; some functions may not be supported.
Short operating range	Weak batteries, obstacles, angle	Replace batteries; ensure clear line-of-sight; aim within 30 degrees.
LED doesn't flash	Batteries installed incorrectly	Check polarity; reinsert batteries.
Cannot learn commands	Original remote not compatible, distance	Use direct code entry; ensure remotes are close (2-3 cm) during learning.
Macro not executing	Programming error, out of range	Reprogram macro; ensure remote is pointed at all devices in sequence.

Reset: Remove batteries for 30 seconds, then reinsert to reset remote memory.

Service: 1-800-222-7669; www.sony.com/support