Sony RMT-D116P Manual

The Sony RMT-D116P is a universal infrared remote control designed for compatibility with various Sony audio/video equipment and select other brands. It features a comprehensive button layout for TV, DVD, VCR, and audio system control, programmable codes, macro functions, and a learning capability. Below are key sections for overview, features, setup, programming, operation, and troubleshooting.

Features at a Glance

Key components: Infrared transmitter, Mode selection buttons (TV, DVD, VCR, AUDIO), Numeric keypad, Navigation pad, Power, Volume/Channel controls, Macro buttons, Learning sensor.

Feature	Description
Universal Compatibility	Pre-programmed codes for Sony and major brand devices
Mode Selection	TV, DVD, VCR, AUDIO modes for controlling up to 4 devices
Macro Function	Program sequence of commands to single button (M1, M2, M3)
Learning Capability	Learn commands from original remote controls
Numeric Keypad	Direct channel/input selection
Navigation Pad	Directional arrows and OK/Enter for menus
Volume/Channel Controls	Dedicated buttons for quick adjustment
Input Select	Switch between video/audio sources
Menu/Guide Buttons	Access device settings and electronic program guide
Battery Indicator	LED flashes when batteries are low

Package Contents

Unpack and verify all items are present.

1. Sony RMT-D116P Remote Control (1 unit)
2. AAA batteries (2 pieces)
3. Quick Start Guide
4. Code list booklet for supported brands and models

WARNING! Keep plastic bags away from children to avoid suffocation hazard.

Initial Setup & Battery Installation

Prepare remote for first use.

1. Open battery compartment on back: Slide cover in direction of arrow.
2. Insert two AAA batteries: Observe correct polarity (+/- markings).
3. Close compartment: Ensure secure latch.
4. Test remote: Point at device, press POWER in corresponding mode (e.g., TV).

CAUTION! Use only AAA batteries. Do not mix old and new or different types. Remove batteries if not used for extended period.

Specifications

• Model: RMT-D116P
• Type: Universal Infrared Remote Control
• Power Source: 2 x AAA batteries (DC 3V)
• Operating Range: Approx. 7 meters (23 feet), within 30-degree angle
• Supported Devices: TVs, DVD players, VCRs, Audio systems, Set-top boxes
• Learning Function: Yes (for non-Sony devices if code not available)
• Macro Buttons: 3 (M1, M2, M3)
• Dimensions: Approx. 200mm x 50mm x 25mm
• Weight: Approx. 100g (including batteries)
• Compliance: FCC Part 15, ICES-003

Button Layout & Functions

Top section: Mode buttons (TV, DVD, VCR, AUDIO). Center: Navigation pad, OK, Menu, Guide. Lower: Numeric, Volume/Channel, Power, Input, Mute, Macro buttons (M1-M3).

Mode Buttons: Press to select device to control (LED indicator lights for active mode). Power: Turns selected device on/off. Volume/Channel: Adjusts audio level or channel up/down. Input: Cycles through video/audio inputs. Mute: Temporarily silences audio. Macro Buttons: Execute programmed command sequences.

Programming the Remote

Two methods: Auto code search or direct code entry.

1. Auto Search: Turn on device. Press and hold MODE button (e.g., TV) until LED blinks twice. Point remote at device, press POWER repeatedly until device turns off. Press OK to save.
2. Direct Code Entry: Find code for your device in code list. Press and hold MODE button until LED blinks twice. Enter 4-digit code using numeric keypad. LED blinks twice if successful.
3. Test functions: Try Volume, Channel, Menu to confirm control.

Tip: If code not found, use Learning function to copy commands from original remote.

Using Macro Functions

Program a sequence of up to 10 commands to a single Macro button (M1, M2, M3).

1. Clear macro: Press and hold MACRO button (e.g., M1) for 3 seconds until LED flashes.
2. Record sequence: Within 20 seconds, press buttons in desired order (e.g., TV POWER, wait 2 sec, DVD POWER, INPUT).
3. End recording: Press same MACRO button again. LED flashes twice.
4. Execute: Press the MACRO button to run entire sequence.

WARNING! Ensure devices are within range and powered. Delays between commands may be needed for device response.

Learning Function

Copy commands from original remote if code not available.

1. Prepare: Place remotes 3-5 cm apart, facing each other.
2. Enter learning mode: Press and hold MODE + MUTE until LED stays on.
3. Select target button: Press button on Sony remote you wish to program (e.g., TV MENU).
4. Teach command: Press corresponding button on original remote. LED blinks if learned.
5. Repeat for other buttons. Press MODE to exit.

Note: Some proprietary or complex signals may not be learned. Infrared only; not for RF or Bluetooth.

Care & Maintenance

Remove batteries before cleaning. Wipe with soft, dry cloth. Do not use solvents or water.

CAUTION! Avoid extreme temperatures, humidity, and direct sunlight. Do not disassemble.

Regulatory Information

FCC Part 15: This device complies with Class B digital device limits. May not cause harmful interference and must accept any interference received. ICES-003: Complies with Canadian ICES-003. Copyright © Sony Corporation. Sony and the Sony logo are trademarks of Sony Corporation. For support, visit www.sony.com/remotesupport or contact 1-800-222-7669.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Batteries/obstructions	Replace batteries; ensure clear line of sight to device IR sensor.
Device does not respond	Wrong mode/not programmed	Select correct mode button; reprogram remote with correct code.
Short operating range	Weak batteries/angle	Replace batteries; point remote directly at device within 30°.
Macro not executing fully	Timing/range	Re-record with longer pauses between commands; ensure all devices in range.
Learning fails	Signal type/distance	Ensure original remote is IR; reduce distance to 3-5 cm; try different button.
LED flashes rapidly	Low battery	Replace both AAA batteries immediately.

Reset: Remove batteries, press all buttons for 10 seconds, reinstall batteries to clear memory.

Service: 1-800-222-7669; www.sony.com/remotesupport