Sony RMT-D120P Manual

The Sony RMT-D120P is a universal remote control designed for compatibility with various Sony and other brand audio/video components. It features pre-programmed codes for TVs, DVD/Blu-ray players, audio systems, and cable/satellite boxes, along with learning capabilities to replace original remotes. Below are key sections for overview, setup, programming, operation, troubleshooting, and specifications.

Features at a Glance

Key components: Ergonomic design, LCD display (on some models), device selection buttons, numeric keypad, navigation controls, and special function keys.

Feature	Description
Device Selection Buttons	TV, DVD, AUDIO, CABLE/SAT, etc. for controlling multiple components
Pre-programmed Codes	Includes codes for major brands (Sony, Samsung, LG, etc.)
Learning Function	Can learn commands from original remotes
Macro Programming	Execute multiple commands with one button (if supported)
Backlit Keys (if applicable)	Illuminated buttons for low-light conditions
Numeric Keypad	For direct channel/input selection
Navigation & OK Button	For menu navigation and selection
Volume & Channel Controls	Dedicated buttons for audio and channel adjustment
Power Button	Turns selected device on/off
Input Select	Cycles through input sources on TV/AV receiver

Initial Setup & Battery Installation

Remove battery cover and insert batteries correctly.

1. Open battery compartment: Slide or press latch to open cover on rear.
2. Insert batteries: Use two AA batteries (alkaline recommended), observing correct polarity (+/-).
3. Close compartment: Secure cover until it clicks.
4. Test remote: Point at device and press POWER for selected component (e.g., TV).

WARNING! Do not mix old and new batteries or different types. Remove batteries if not used for extended periods to prevent leakage.

Programming the Remote

Program using pre-set codes or auto-search.

1. Turn on device to be controlled (e.g., TV).
2. Press and hold device button (e.g., TV) until indicator light blinks twice.
3. Enter 3-digit code from code list (see manual appendix).
4. Point remote at device and press POWER. If device turns off, programming is successful.
5. If not, repeat with next code or use auto-search: Hold SETUP until light blinks, then press POWER repeatedly until device turns off, then press ENTER to save.

CAUTION! Keep original remote for learning function if needed. Ensure line-of-sight to device during programming.

Specifications

• Model: RMT-D120P Universal Remote.
• Power Source: 2 x AA batteries (not included).
• Operating Range: Approx. 6 meters (line-of-sight).
• Compatible Devices: TVs, DVD/Blu-ray players, audio systems, cable/satellite boxes, streaming devices.
• Learning Capacity: Up to 20 commands (if supported).
• Infrared Frequency: Standard IR protocol.
• Dimensions: Standard remote size (approx. 150mm x 50mm x 20mm).
• Weight: Lightweight ergonomic design.
• Warranty: Refer to Sony warranty terms.

Button Layout & Functions

Top section: Device buttons (TV, DVD, AUDIO, CABLE/SAT). Center: Navigation ring with OK, MENU, GUIDE, EXIT. Lower: Numeric keypad, VOLUME/CHANNEL, MUTE, POWER, INPUT.

Special Functions: SUBTITLE, AUDIO, INFO, FAVORITE, RECORD (for DVR). Macro: Hold two device buttons to program sequence (if supported).

Indicator Light: Blinks to confirm commands/programming. Lock Feature: Hold CLEAR and 0 to disable keys (prevents accidental presses).

Learning Function (Code Learning)

Teach remote commands from original remote.

1. Place remotes facing each other (3-5 cm apart).
2. Press and hold LEARN (or SETUP+device button) until light blinks.
3. Press button on RMT-D120P to be programmed.
4. Press corresponding button on original remote; light blinks twice if learned.
5. Repeat for other buttons; press SETUP to exit.

Tip: Ensure batteries are fresh. Learning may not work for all commands (e.g., RF or Bluetooth).

Operating Multiple Devices

Control up to 4-5 components with device buttons.

1. Select device: Press TV, DVD, etc. Indicator may blink.
2. Operate: Use volume/channel for that device; some buttons (POWER, INPUT) are device-specific.
3. Volume Lock: Set volume to always control audio system (see advanced setup).

Note: Some functions (like numeric keys) may be shared across devices. Refer to code list for brand-specific behavior.

Resetting the Remote

Clear all programming to factory defaults.

Method 1: Remove batteries, press all buttons for 10 seconds, reinsert batteries. Method 2: Press and hold SETUP and CLEAR together for 5 seconds until light blinks rapidly.

WARNING! Reset erases all learned codes and custom settings. Re-program devices after reset.

Care & Maintenance

Wipe with dry, soft cloth. Avoid moisture, heat, and dropping.

CAUTION! Do not use chemicals or abrasive cleaners. Keep away from children and pets.

Regulatory & Compliance

FCC Part 15: Class B digital device; complies with interference limits. Sony and logo are trademarks of Sony Corporation. For support, visit www.sony.com/remotesupport or contact Sony Customer Service at 1-800-222-7669.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Batteries/obstructions	Replace batteries; ensure line-of-sight; remove obstacles.
Cannot program device	Wrong code/range	Use correct code from list; try auto-search; reduce distance.
Learning fails	Low battery/original remote issue	Use fresh batteries; ensure original remote is IR (not RF); point directly.
Buttons unresponsive	Lock mode activated	Disable lock (press CLEAR+0 again); reset remote.
Intermittent operation	Weak batteries/interference	Replace batteries; avoid strong light sources (sunlight, LEDs) near sensor.

Reset: Use reset procedure above if issues persist.

Service: 1-800-222-7669; www.sony.com/support