Sony RMT-D128P Manual

The Sony RMT-D128P is a universal remote control designed for compatibility with various Sony and other brand audio/video components. It features pre-programmed codes for TVs, DVD/Blu-ray players, audio systems, and cable/satellite boxes, along with learning capabilities, macro functions, backlit keys, and an ergonomic design. Below are key sections for overview, setup, programming, operation, features, and troubleshooting.

1. Overview & Package Contents 2. Initial Setup & Battery Installation 3. Programming the Remote 4. Specifications 5. Button Layout & Functions 6. Learning Function 7. Macro Programming 8. Advanced Features 9. Care & Maintenance 10. Regulatory & Compliance 11. Troubleshooting

Overview & Package Contents

The RMT-D128P allows control of up to 8 devices, with direct access buttons for common functions. It includes a comprehensive code library and can learn commands from original remotes.

Item	Description
Sony RMT-D128P Remote Control	Main universal remote unit
User Manual	This guide
Two AA Batteries	For power (pre-installed or included separately)
Quick Start Guide	Basic setup instructions

Initial Setup & Battery Installation

Prepare the remote for first use by installing batteries and selecting the device mode.

Open battery compartment on rear.
Insert two AA batteries, observing correct polarity (+/-).
Close compartment securely.
Press any button to activate; backlight may illuminate briefly.

WARNING! Use only recommended battery types. Do not mix old and new batteries. Remove batteries if not using for extended periods.

Programming the Remote

Program the remote to control your devices using auto-search or direct code entry.

Turn on the device you want to control (e.g., TV).
Press and hold the corresponding device button (TV, DVD, etc.) until indicator light stays on.
Enter the 3-digit code for your brand (see code list in manual).
Point remote at device and press POWER; if device turns off, press ENTER to save.
For auto-search: Hold device button until light stays on, then press CH+ repeatedly until device turns off, then press ENTER.

Tip: Test volume and channel controls after programming to ensure full functionality.

Specifications

Model: RMT-D128P
Power Source: 2 x AA batteries (1.5V)
Battery Life: Approximately 12 months with typical use
Operating Range: Up to 8 meters (26 feet)
Angle of Operation: ±30 degrees
Supported Devices: TV, DVD/Blu-ray, Audio System, Cable/Satellite, Game Console, etc.
Learning Capacity: Up to 20 commands
Macro Capacity: Up to 10 macros with 10 steps each
Backlight: Blue LED backlight for keypad
Dimensions: Approx. 220mm x 50mm x 25mm
Weight: Approx. 150g (with batteries)

Button Layout & Functions

Top row: Device selection buttons (TV, DVD, AUDIO, CABLE, etc.). Navigation: Directional pad, OK/ENTER, MENU, GUIDE, INFO. Transport: PLAY, PAUSE, STOP, REC, FF, REW. Volume/Channel: VOL +/-, CH +/-, MUTE. Special: BACKLIGHT, LEARN, MACRO, NUMBER PAD, POWER.

Backlight: Press BACKLIGHT to illuminate keys for 5 seconds in low light.

Learning Function

Teach the remote commands from your original remote if code is not pre-programmed.

Place both remotes facing each other, 2-5 cm apart.
Press and hold LEARN button until indicator flashes twice.
Press device button (e.g., TV) you want to assign learned command to.
Press the key on RMT-D128P you wish to program (e.g., VOL+).
Press and hold corresponding button on original remote until RMT-D128P light flashes twice.
Repeat for additional keys; press LEARN to exit.

Note: Some proprietary functions may not be learnable. Ensure original remote is IR type.

Macro Programming

Program a sequence of commands to execute with one button press (e.g., "Watch DVD" turns on TV, DVD player, and switches input).

Press and hold MACRO button until indicator flashes.
Press the device button where you want to store macro (e.g., DVD).
Press the key you wish to assign as macro trigger (e.g., PLAY).
Press the sequence of remote buttons you want in macro (max 10 steps).
Press MACRO again to save; indicator flashes twice.
Test by pressing the assigned macro key.

Tip: Insert 1-second delays between steps for reliable execution by adding PAUSE button in sequence.

Advanced Features

Device Lock: Hold device button + CLEAR for 3 seconds to lock/unlock accidental key presses. Factory Reset: Press and hold TV + DVD + POWER for 5 seconds to clear all programming. Code Search: Use auto-search method if code unknown.

Care & Maintenance

Clean with dry, soft cloth. Avoid liquids, extreme temperatures, and humidity. Replace batteries when backlight dims or range decreases.

CAUTION! Do not disassemble; no user-serviceable parts inside.

Regulatory & Compliance

FCC Part 15 Class B compliant. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the condition that this device does not cause harmful interference. Contains transmitter module FCC ID: AK8RMTSD128P. Disposal: Follow local regulations for battery and electronic waste.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Dead batteries, obstruction	Replace batteries; ensure clear line of sight to device sensor.
Cannot program device	Incorrect code, device not supported	Try auto-search; verify device is on code list; use learning function.
Short operating range	Weak batteries, interference	Replace batteries; remove obstacles; avoid direct sunlight on sensor.
Backlight not working	Battery low, disabled	Replace batteries; press BACKLIGHT firmly.
Macro not executing fully	Steps too rapid, device not responding	Re-program with PAUSE between steps; ensure devices are on.
Learning fails	Original remote not IR, too far	Use original IR remote; reduce distance to 3-5 cm; ensure original remote batteries are good.

Support: For help, visit www.sony.com/remotesupport or call 1-800-222-7669.