Sony RMT-D150P Manual

The Sony RMT-D150P is a universal remote control designed for compatibility with a wide range of Sony audio/video equipment. It features a comprehensive button layout for TV, DVD/Blu-ray, audio system, and set-top box control, with programmable functions, macro capabilities, and backlit buttons for low-light operation. Below are key sections for overview, setup, programming, operation, and troubleshooting.

Features at a Glance

Key components: Universal remote control with LCD display, Device selection buttons (TV, DVD/BD, AUDIO, CABLE/SAT), Numeric keypad, Navigation pad, Transport controls (Play, Pause, Stop, etc.), Volume/Channel controls, Macro buttons, Backlight.

Feature	Description
Universal Compatibility	Controls up to 4 devices (TV, DVD/Blu-ray, Audio System, Cable/Satellite Box)
LCD Display	Shows device mode, macro labels, and status information
Macro Function	Program sequence of commands to multiple devices with single button press
Backlit Buttons	Illuminated keypad for use in low-light conditions
Learning Function	Can learn commands from original equipment remotes (if supported)
Device Select Buttons	TV, DVD/BD, AUDIO, CABLE/SAT for switching control modes
Navigation Pad	Directional arrows and Enter for menu navigation
Transport Controls	Play, Pause, Stop, FF, REW, Skip, Record
Volume/Channel	Dedicated buttons for volume up/down and channel up/down
Power	Separate power buttons for each device mode

Package Contents

Unpack and verify all items are present.

1. Sony RMT-D150P Remote Control
2. Two AA batteries
3. Quick Setup Guide
4. Warranty Information Card

NOTE: If any item is missing or damaged, contact Sony customer support.

Initial Setup & Battery Installation

Prepare remote for first use.

1. Open battery compartment on rear of remote.
2. Insert two AA batteries, observing correct polarity (+/-).
3. Close battery compartment securely.
4. Point remote at device and test basic functions (Power, Volume).
5. If remote doesn't respond, proceed to Programming section.

CAUTION! Use only recommended battery types. Do not mix old and new batteries or different types.

Specifications

• Model: RMT-D150P
• Power Source: 2 x AA batteries (included)
• Battery Life: Approximately 6 months with normal use
• Operating Range: Up to 7 meters (23 feet)
• Angle of Operation: ±30 degrees
• Infrared Wavelength: 940 nm
• Supported Devices: TVs, DVD/Blu-ray players, Audio systems, Cable/Satellite boxes
• Learning Capability: Yes (for compatible commands)
• Macro Memory: Stores up to 3 macros
• Dimensions: Approx. 220mm x 50mm x 30mm
• Weight: Approx. 150g (with batteries)

Button Layout & Functions

Top section: LCD display shows active device and macro labels. Device selection buttons: TV (red), DVD/BD (blue), AUDIO (green), CABLE/SAT (yellow).

Common Functions: POWER (per device), MUTE, VOL+/-, CH+/-, NUMBER (0-9), ENTER, MENU, GUIDE, EXIT, INFO, RETURN.

Transport Controls: PLAY, PAUSE, STOP, FF, REW, SKIP+/-, REC.

Navigation: Arrow buttons (Up/Down/Left/Right), ENTER.

Special: MACRO (M1, M2, M3), BACKLIGHT (lights buttons for 5 seconds), LEARN (for programming from other remotes).

Programming the Remote

Three methods: Auto code search, Direct code entry, Learning function.

1. Auto Code Search:
   • Turn on device to be controlled.
   • Press and hold device button (TV/DVD/etc.) until LED blinks twice.
   • Point remote at device and press POWER repeatedly until device turns off.
   • Press ENTER to save code.
2. Direct Code Entry:
   • Find correct code for your device in code list (see manual appendix).
   • Press and hold device button until LED blinks twice.
   • Enter 4-digit code using number pad.
   • LED blinks twice if code accepted.
3. Learning Function:
   • Place original remote head-to-head with RMT-D150P.
   • Press LEARN on RMT-D150P, then press button to program.
   • Press corresponding button on original remote.
   • LED blinks to confirm learning.

Macro Function Setup

Program sequence of commands to multiple devices.

1. Press and hold MACRO button for 3 seconds until LED lights.
2. Select macro button (M1, M2, or M3) to program.
3. Press device and command buttons in desired sequence (e.g., TV POWER, DVD/BD POWER, AUDIO POWER).
4. Wait 1 second between commands.
5. Press MACRO again to save sequence.
6. Test macro by pressing assigned M button.

Example Macro: "Watch DVD" = Turn on TV, switch to HDMI input, turn on DVD player, turn on audio system.

Using with Multiple Devices

Switch between controlled devices.

1. Press corresponding device button (TV, DVD/BD, AUDIO, CABLE/SAT).
2. LCD displays active device icon.
3. All subsequent commands control that device until another device button is pressed.
4. Use POWER button specific to each device mode.

Tip: For quick volume control while watching TV, ensure TV mode is selected before adjusting volume.

Care & Maintenance

Remove batteries if not using for extended period. Clean with dry, soft cloth. Do not use chemicals or abrasives.

CAUTION! Do not expose to extreme temperatures, moisture, or direct sunlight. Keep away from children.

Regulatory Information

FCC Compliance: This device complies with Part 15 of FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received. Copyright © Sony Corporation. All rights reserved. Sony and the Sony logo are trademarks of Sony Corporation. For support, visit www.sony.com/support or contact 1-800-222-7669.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote doesn't work	Dead batteries, obstacles, wrong mode	Replace batteries; clear line of sight; press correct device button.
Some buttons don't work	Not programmed, device incompatible	Reprogram remote; check device compatibility list.
Macro doesn't execute	Sequence too long, delay incorrect	Reduce commands in macro; ensure 1-second delay between commands.
Learning function fails	Original remote not compatible, distance too great	Use direct code entry instead; place remotes closer together.
Backlight doesn't work	Battery low, function disabled	Replace batteries; ensure BACKLIGHT button is pressed firmly.
LCD display dim or blank	Battery low, normal operation	Replace batteries; display only activates during programming.

Reset: Remove batteries for 30 seconds, then reinstall to reset remote to factory defaults.

Service: 1-800-222-7669; www.sony.com/support