Sony RMT-VB200U Manual

The Sony RMT-VB200U is a universal remote control designed for compatibility with a wide range of Sony and other brand audio/video equipment. It features a simple layout with essential buttons for power, volume, channel control, numeric input, and source selection. Below are key sections covering features, setup, operation, programming, battery information, and troubleshooting.

Features at a Glance

Key components: Ergonomic design, clearly labeled buttons, infrared transmitter, battery compartment.

Feature	Description
Universal Compatibility	Controls TVs, DVD/Blu-ray players, audio systems, and cable/satellite boxes from various brands.
Direct Code Entry	Program using manufacturer codes for quick setup.
Code Search	Automatically searches for correct device code if direct code is unknown.
Device Select Buttons	Dedicated buttons (TV, DVD, AUDIO, CABLE/SAT) to control multiple devices.
Essential Controls	Power, Volume, Channel, Mute, Numeric Keypad, Menu, Navigation, and Input/Source.
Battery Powered	Uses two AAA batteries (included).

Package Contents

• Sony RMT-VB200U Remote Control (1)
• AAA Batteries (2)
• Quick Start Guide

NOTE: Ensure all items are present before proceeding. Contact your retailer if anything is missing.

Remote Control Layout

Top Section: POWER button.

Device Selection Area: TV, DVD, AUDIO, CABLE/SAT buttons.

Central Navigation: Directional Arrow Pad (Up/Down/Left/Right), OK/SELECT button in center.

Key Functional Buttons: MENU, GUIDE/INFO, EXIT/BACK, VOLUME (+/-), CHANNEL (+/-), MUTE.

Numeric Keypad: Numbers 0-9, CH RTN (Channel Return).

Bottom Section: INPUT/SOURCE, PLAY, PAUSE, STOP, PREV/NEXT (Track/Chapter).

Battery Installation

1. Slide the battery cover on the back of the remote downward to open.
2. Insert two AAA batteries, observing the correct polarity (+/-) as marked inside the compartment.
3. Replace the battery cover by sliding it back into place until it clicks.

WARNING! Do not mix old and new batteries or different battery types. Remove batteries if the remote will not be used for an extended period to prevent leakage.

Initial Setup & Device Programming

To program the remote to control your device (e.g., a TV):

1. Turn on the device you want to control (e.g., your TV).
2. On the remote, press and hold the corresponding device button (e.g., TV) until the indicator light stays on.
3. While the light is on, enter the 3-digit or 4-digit manufacturer code for your device (see code list in manual appendix). The light will blink twice if the code is accepted.
4. Aim the remote at the device and press the POWER button. The device should turn off. If it does not, repeat steps 2-3 with another code from the list.

Tip: Have your device's model number ready to find the correct code quickly.

Basic Operation

1. Select a Device: Press the button (TV, DVD, etc.) for the device you want to control. The remote will send signals to that device until you press another device button.
2. Control Functions: Use the standard buttons (Volume, Channel, Navigation, Play, etc.) as you would with the original remote.
3. Volume Lock (TV Mode): Some setups allow the TV volume button to control an external audio system. Refer to your audio system's manual for A/V sync setup details.

Advanced Programming (Code Search)

Use this method if you do not know the manufacturer code:

1. Turn on the device you want to control.
2. Press and hold the desired device button (e.g., TV) and the POWER button simultaneously until the indicator light stays on.
3. Press the POWER button repeatedly, pausing a second between presses, until the device turns off.
4. Once the device turns off, immediately press the OK/SELECT button to store the code. The indicator light will blink twice.
5. Test other functions (Volume, Mute) to confirm programming is complete.

Resetting the Remote

To clear all programmed settings and restore factory defaults:

1. Press and hold the TV button and 1 button simultaneously for about 5 seconds. The indicator light will blink several times.
2. Release the buttons. All previous programming for all device modes is now erased.
3. You must reprogram the remote for each device you wish to control.

CAUTION! This action cannot be undone. Only perform a reset if necessary.

Care & Maintenance

• Use a soft, dry cloth to clean the remote. Do not use solvents or abrasive cleaners.
• Keep the remote away from excessive heat, humidity, and direct sunlight.
• Do not drop or subject the remote to strong impacts.
• Replace batteries when the operating range decreases significantly.

CAUTION! Do not disassemble the remote. There are no user-serviceable parts inside.

Specifications

• Model: RMT-VB200U
• Power Source: 2 x AAA (1.5V) batteries
• Operating Range: Approx. 23 feet (7 meters) at an angle of +/- 30 degrees.
• Infrared Wavelength: 940 nm
• Supported Devices: TVs, DVD/Blu-ray Disc players, Audio Systems, Cable/Satellite Set-top Boxes.
• Dimensions (Approx.): 6.3" x 2.2" x 0.8" (160mm x 55mm x 20mm)
• Weight (with batteries): Approx. 3.5 oz (100g)

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote does not work	Dead batteries, obstruction, wrong device selected.	Replace batteries; ensure clear path to device's IR sensor; press correct device button (TV, DVD, etc.).
Only some buttons work	Incorrect device code programmed.	Reprogram the remote using the correct manufacturer code or Code Search method.
Short operating range	Weak batteries, low battery, obstacles.	Replace with fresh batteries; ensure direct line of sight to device.
Remote controls wrong device	Device codes overlap.	Move the other device out of line of sight temporarily, or reprogram one device with a different code if available.
Indicator light does not come on	Batteries inserted incorrectly or dead.	Check battery polarity and contacts; install new batteries.

Support: For further assistance, code lists, or product information, visit the Sony support website at www.sony.com/support or consult the full manual.